UsTube

Text to SRT Converter

Paste a script and get an SRT file with cues split by sentence and line length. Timing is worked out from a reading speed or spread over a duration you give.

Drop a file here, or tap to choose .txt file or any text file. Read in your browser and never uploaded.

Timings are estimates made from the length of the text. They are not matched to any audio. Play the video with the file and correct the times where they drift.

Runs in your browser. Nothing you type or open here is uploaded.

How it works

How to turn text into an SRT file

  1. 1

    Paste your script

    Paste the text, or drop a .txt file. Put each paragraph or speech on its own line, so cues do not run across them.

  2. 2

    Set line length and timing

    The defaults are 42 characters per line, two lines and 16 characters per second. Or choose to spread the text over a total duration.

  3. 3

    Download and check

    Press Download file, load the SRT in your editor or player, and move the times that are off.

What this tool does with your text

You paste a script. The tool splits it into subtitle cues, wraps each cue into short lines, and gives every cue a start and an end time. The result is a standard SRT file: a number, a time range with commas, and the text.

How the text is split

  • A line break in your text always ends a cue. Use it to separate speakers or scenes.
  • A sentence ends at a full stop, question mark or exclamation mark. Common short forms such as "Mr." and "e.g." do not end a sentence.
  • A sentence that is too long for one cue is cut into parts of about equal length, so you do not get a cue with one or two words left over.
  • Lines are wrapped at the number of characters you choose, and a two-line cue is balanced so the lines are close in length.

Choosing the numbers

Many subtitle style guides ask for lines of about 42 characters, two lines at most, and a reading speed of roughly 15 to 17 characters per second for adult viewers. These are the defaults. Children's programmes and difficult text need a lower speed. A cue also stays on screen for at least the minimum length you set, one second by default, even if the text is very short.

Reading speed or total duration

With a reading speed, each cue lasts as long as its text needs. With a total duration, the time you give is shared between the cues in proportion to their length. Use that mode when you already know the clip is, say, two minutes and thirty seconds long. The page shows the average speed and warns you when it is too fast to read.

These timings are estimates

The tool cannot hear your audio. It guesses from how long the text is, so natural pauses and a speaker who talks fast or slow will not match. Treat the file as a first draft. Load it with the video and move the times that are wrong. If everything is off by the same amount, the subtitle shifter fixes it in one step.

Related steps

Not sure how long your script is to speak? Check it with the words to minutes calculator. To read a script on camera, use the online teleprompter. For web players you can then convert the file with the SRT to VTT converter.

Free video editor

Edit it in your browser.

UsTube's editor has a full timeline, auto captions, music, effects and 1080p export with no watermark. Nothing to install.

Open the free editor Free to start · no card needed

Questions people ask

How do I create an SRT file from text?
Paste the text, check the line length and timing options, and press Download file. The file is a standard .srt that works in editors and players.
How are the subtitle times decided?
From the length of each cue and the reading speed you set, or by sharing a total duration between the cues by length. They are estimates, not matched to audio.
What is a good characters-per-line setting?
About 42 characters per line and two lines is common. Use fewer characters for small phone screens or vertical video.
What reading speed should I use?
Around 15 to 17 characters per second suits most adult audiences. Use a lower number for children or for hard text.
Can I make the subtitles match my audio exactly?
Not with this tool. Use it for a first draft, then adjust times in a subtitle editor or with the subtitle shifter if everything is early or late by the same amount.
Does it work with other languages?
Yes. Any language works, and sentence ends such as the Urdu full stop and the Arabic question mark are recognised. The file is saved as UTF-8.
Free tools

More tools like this

See all 54 free tools